Advanced Search

    column
    Revision Recommendations of GB/T 228.1-2010 and ISO 6892-1: 2016 for Tensile Test Method Standards of Metallic Materials at Room Temperature
    LI Heping
    2018, 54(9): 621-628,646. DOI: 10.11973/lhjy-wl201809001
    Abstract PDF
    Several Controversial Issues during the Implementation of GB/T 228.1-2010 and ISO 6892-1: 2016
    ZHANG Xianfeng, GAO Yuhao, CAI Haichen, SHAN Jianjun
    2018, 54(9): 629-631,656. DOI: 10.11973/lhjy-wl201809002
    Abstract PDF
    Difference Analysis between National and American Standards of Tensile Test Method and Revision Suggestions on the National Standard
    ZHOU Zhichao
    2018, 54(9): 632-635,652. DOI: 10.11973/lhjy-wl201809003
    Abstract PDF
    Analysis on Corresponding Relations of Correlative Test Rates for Tensile Test of Metallic Materials under the Control of Displacement Rate
    WU Yong, ZHANG Zhijun, LI Ji
    2018, 54(9): 636-640,675. DOI: 10.11973/lhjy-wl201809004
    Abstract PDF
    Application and Status of High-Strain Rate Tensile Test of Metallic Materials
    LIU Pengpeng, YE You, WEI Yifan, WANG Caimei, LI Yingchao
    2018, 54(9): 641-646. DOI: 10.11973/lhjy-wl201809005
    Abstract PDF
    Comparison and Analysis of Different Standard System Requirements for Tensile Test of Nuclear Power Metallic Materials
    LI Wanmin, CHEN Yunlong, TIAN Hongzhi
    2018, 54(9): 647-649,675. DOI: 10.11973/lhjy-wl201809006
    Abstract PDF
    Analysis on Influencing Factors of Tensile Test Accuracy for Steel Plates
    LIANG Yanyan, PENG Xiaofeng
    2018, 54(9): 650-652. DOI: 10.11973/lhjy-wl201809007
    Abstract PDF
    Influence Factors on Measurement of Specified Plastic Elongation Strength for Hot-Dip Galvanized Sheets
    LI Yan, WANG Yilei
    2018, 54(9): 653-656. DOI: 10.11973/lhjy-wl201809008
    Abstract PDF
    Evaluation on Measurement Uncertainty of Tensile Test of Metallic Materials at Room Temperature
    ZHAO Yongfeng, LIN Xiaogang, CHEN Jie, TANG Zhigang
    2018, 54(9): 657-661. DOI: 10.11973/lhjy-wl201809009
    Abstract PDF
    Analysis on Failure Influence Factors and Examples of Steel Balls
    GUO Hao, LEI Jianzhong, ZHANG Yongzhen, HU Linzhuang
    2018, 54(9): 662-668,688. DOI: 10.11973/lhjy-wl201809010
    Abstract PDF
    Viscosity Testing Practice of Mold Casting Powders
    LI Yunping
    2018, 54(9): 669-671,704. DOI: 10.11973/lhjy-wl201809011
    Abstract PDF
    Comparison and Application of Common Stress Corrosion Standard Test Methods
    DANG Hengyao, ZHANG Yajun, LUO Xianfu, ZHANG Wenli
    2018, 54(9): 672-675. DOI: 10.11973/lhjy-wl201809012
    Abstract PDF
    Failure Analysis on Fracture of Adjust Stud in Metro Pantograph
    XUAN Dongsheng, ZHANG Libing, SHEN Xian, LIU Haibo, ZHANG Peng, WANG Hui
    2018, 54(9): 676-679,691. DOI: 10.11973/lhjy-wl201809013
    Abstract PDF
    Failure Analysis on Leakage of Heating Surface Tubes of Waste Heat Boilers
    WANG Zhichun, WANG Wenling, CAI Wenhe, ZHAO Weidong, YANG Shaoxuan
    2018, 54(9): 680-684. DOI: 10.11973/lhjy-wl201809014
    Abstract PDF
    Cause Analysis on Fracture of Condensate Pump Shaft
    ZHANG Fanzhi, YANG Linhao, PENG Yichao, WANG Xianming, XU Haohao
    2018, 54(9): 685-688. DOI: 10.11973/lhjy-wl201809015
    Abstract PDF
    Failure Analysis on Burst of Water Wall Tube in a Power Plant
    REN Kai
    2018, 54(9): 689-691. DOI: 10.11973/lhjy-wl201809016
    Abstract PDF
    Cause Analysis on Fracture of a 220 kV Transmission Wire
    WANG Kun, ZHENG Zhunbei, YANG Zhanjun, SUN Xiaoping
    2018, 54(9): 692-697. DOI: 10.11973/lhjy-wl201809017
    Abstract PDF
    Cause Analysis on Fracture of Driving Bevel Gear for Forklift
    DAI Shenmei
    2018, 54(9): 698-700,704. DOI: 10.11973/lhjy-wl201809018
    Abstract PDF
    Cause Analysis on Unqualified Elongation after Fracture of Q235B Steel Plates
    LIU Weihang
    2018, 54(9): 701-704. DOI: 10.11973/lhjy-wl201809019
    Abstract PDF