Advanced Search

    column
    STRESS ANALYSIS ON ARBITRARY SECTION UNDER BOTH APPLIED AND SURFACE RESIDUAL STRESSES FOR CYLINDRICAL HELICAL COMPRESSION SPRING
    WANG Ren-zhi, YANG Wei-ming, WU Qu-ling
    2007, 43(1): 1-5.
    Abstract PDF
    THE INFLUENCE OF TENSILE TEST RATE ON MECHANICAL PROPERTY OF LOW CARBON STEEL
    ZENG Li
    2007, 43(1): 6-8.
    Abstract PDF
    THE CONTROL OF SURFACE DECARBONIZATION IN THE HOT ROLL PROCESS FOR Si-BEARING MEDIUM CARBON STEEL
    SUI Xiao-hong
    2007, 43(1): 9-11.
    Abstract PDF
    SUPERFICIAL VIEW ON THE RELATIONS BETWEEN IE VALUE AND ELONGATION AFTER BREAK OF THE LOW CARBON COLD ROLLED STEEL SHEET THINNER THAN 1mm
    GU Wei, XU Yu-yu, ZHOU Jian-feng
    2007, 43(1): 12-14.
    Abstract PDF
    THE PROPERTIES COMPARISON BETWEEN ZnO THIN FILMS FABRICATED BY ION BEAM SPUTTERING AND RF MANGNETRON SPUTTERING
    GU Jin-bao, LI He-qin, ZHAO Zhi-ming
    2007, 43(1): 15-18.
    Abstract PDF
    A PRECISION MEASURE OF MORRIS WEIGHTED FACTOR ξ(hkl) IN HARRIS-MUELLER INVERSE POLE FIGURE——LG METHOD
    YANG Jin, YIN Zhi-min, YANG Guo-tao
    2007, 43(1): 19-22.
    Abstract PDF
    METHOD VALIDATION OF DIGITAL PHOTOMICROGRAPHING AND IMAGE ANALYZING INSTALLED IN THE METALLUGICAL MICROSCOPE
    BI Ge-pin, YANG Dong
    2007, 43(1): 23-26.
    Abstract PDF
    STUDY ON BORIDES AND ITS COMPOSITES
    YOU Shu-li, YU Zhi-qiang, YANG Zhen-guo
    2007, 43(1): 27-31.
    Abstract PDF
    THE FAILURE ANALYSIS OF THE CRACKED BOILER TUBES
    WANG Bing-ying, LIU Wei-qiang
    2007, 43(1): 32-34.
    Abstract PDF
    SURFACE HYDROGEN-INDUCED BLISTERING ANALYSIS OF SQUARE PIPE
    BA Fa-hai
    2007, 43(1): 35-37.
    Abstract PDF
    SPHEROIDALIZATION OF NODULAR CAST IRON PINCER SEAT
    YU Qing-feng, LIU Qing-hong
    2007, 43(1): 38-39.
    Abstract PDF
    STRESS CORROSION FAILURE ANALYSIS OF THE FASTENING BOLT AT HEAT EXCHANGER
    YOU Xiang-qun, DU Hong-jian, GU Zhi-gang
    2007, 43(1): 40-42.
    Abstract PDF
    INTRODUCTION TO STEEL-DETERMINATION OF CONTENT OF NONMETALLIC INCLUSIONS-MICROGRAPHIC METHOD USING STANDARDS DIAGRAMS GB/T 10561-2005
    HE Qun-xiong, SUN Shi-qiu
    2007, 43(1): 43-47.
    Abstract PDF
    APPLICATION OF THE AUTOMATIC POLISH-GRINDING MACHINE IN METALLOGRAPHIC TEST
    XU Dao-yuan, YANG Li-zhu
    2007, 43(1): 48-49.
    Abstract PDF
    SOME TYPICAL EXAMPLES OF IMMEDIATE EVALUATION METHOD AND SYNTHETIC EVALUATION METHOD FOR THE MEASUREMENT OF UNCERTAINTY ——LECTURE No.4 THE SYNTHETIC EVALUATION METHOD AND ITS EXAMPLES 3——THE EVALUATION OF MEASUREMENT UNCERTAINTY FOR BRINELL HARDNESS TEST OF METALLIC MATERIALS (CONTINUE)
    2007, 43(1): 50-54.
    Abstract PDF